Short Spindle Clock Movement (3mm dial) & Hands
Short Spindle Clock Movement (3mm dial) & Hands
Short Spindle Clock Movement (3mm dial) & Hands
Short Spindle Clock Movement (3mm dial) & Hands
Short Spindle Clock Movement (3mm dial) & Hands

Short Spindle Clock Movement (3mm dial) & Hands

£3.95
Stock Status: In Stock
Just the TICKet for handmade clocks
Facebook
Instagram
Youtube
Twitter
Pinterest
You will earn 3 points with this purchase
Information
A Short Spindle Clock Movement & Hands designed for dials up to 3mm thick (e.g a CD or very thin piece of artwork). This high quality quartz clock mechanism has a hanger for ease of display and a continuously sweeping second hand.

BONUS: A clear CD centre adaptor is included with this movement. These adaptors are designed to reduce the size of the CD centre hole to take our clock movements.

Measurements of movement:

  • 70mm high (with hanger) x 55mm wide x 16mm deep (without spindle)
  • The height of the movement without the hanger is 55mm
  • Centre hole needed in dial 8mm to 10mm
  • The full length of the Medium spindle (Movement case to tip of spindle) is 13mm
Choose from the following hands (all including hour, minute and second hands):
  • 47mm Teardrop Gold - specifically for CD size clocks (12mm diameter)
  • 47mm Teardrop Silver - specifically for CD size clocks (12mm diameter)
  • 48mm Double Teardrop Gold - specifically for CD size clocks (12mm diameter)
  • 55mm Rounded Gold - ideal for our 15cm Clock Face MDF board
  • 55mm Rounded Silver - ideal for our 15cm Clock Face MDF board
  • 110mm Teardrop Gold - decorative hands for our 25cm Clock Face MDF board
  • 110mm Teardrop Silver - decorative hands for our 25cm Clock Face MDF board
  • 110mm Teardrop Black - decorative hands for our 25cm Clock Face MDF board
  • 119mm Plain Gold - square ended hands for our 25cm Clock Face MDF board (these can be cut down)
  • 119mm Plain Silver - square ended hands for our 25cm Clock Face MDF board (these can be cut down)
  • 119mm Plain Black - square ended hands for our 25cm Clock Face MDF board (these can be cut down) - these have a gold button on the second hand
Fitting Instructions

Movement: To make a clock you will need an 8mm to 10mm hole in the dial. Place the rubber washer (supplied) over the movement spindle and push the spindle through the hole from the back of the dial. Place a brass washer (not supplied) over the spindle (this covers any small chips or ragged edges around the hole), then just tighten the brass nut (supplied) on the thread until the movement is held firmly. Please be careful not to over tighten the nut as this can distort the cogs in the movement and stop it from working.

Hands: If you are using metal hands they normally have a polythene protective coating that needs removing. For safety reasons clock hands are deliberately made to be a very tight fit on clocks and when fitting clock hands there is a technique to use! It can help to fit the hour and minute (not the second) hands to the spindle before fitting the movement to the clock as can remove any small machining burr on the hands or movement spindle making fitting much easier when the movement has been fitted. Please hold the back of the movement case in to support it with one hand then hold the centre of the hour hand firmly and turn and wriggle it whilst gradually pushing it on to the movement spindle whilst making sure it is pointing to the 12. Repeat the process with the minute hand, again ensuring it is pointing to the 12. Finally, use the winder on the back of the movement to make sure the hands complete a full 12 hour cycle without touching together. If they do, just bend them slightly to move them apart then put in the battery and that's it. A new alkaline battery (not included) should last for several months and our clock movements are guaranteed for 12 months.

Please be careful not to destroy your clock movement by removing the second hand after it is fitted! The second hand fits VERY tightly as it is a metal to metal fit It is NOT intended to be removed after fitting as this can pull the metal hand spindle out of the movement which WILL destroy the movement! For this reason please don't push it on to the spindle too tightly, especially if you may want to remove it again. When you finally fit the second hand just push it on to the spindle enough to ensure it is firmly applied.
Specifications
  • Product Code:
    EMB.005.001.001.010
  • Type:
    Clock
  • Shape:
    Plain
  • Colour:
    Silver
c